Hunka Burnin’ Love Cake Recipe

Instructions

Make the Cake

1. Preheat the oven to 300°F [150°C]. Spray the sides and bottoms of two 8-in [20-cm] diameter round cake pans with nonstick cooking spray. Set aside.
2. In a medium bowl, combine the flour, cocoa powder, salt, baking powder, and baking soda. Whisk together until well blended. Set aside.
3. In the bowl of a stand mixer fitted with the paddle attachment, place the butter and sugar and cream on medium speed until light and fluffy. Scrape down the sides of the bowl as needed to make sure there are no unincorporated chunks of butter. Add the eggs, one at a time, to the butter mixture, beating to incorporate each egg completely before adding the next one. Add the vanilla extract. Mix until the batter is light and creamy.
4. On low speed, add the dry mixture in three parts, alternating with the buttermilk. Begin with dry ingredients and end with the buttermilk, mixing after each addition.
5. Divide the batter equally between the two pans. Spread it evenly to cover the entire bottom of the pan. The more evenly you spread the batter, the more even the cake layers will be.
6. Bake for 40 to 45 minutes. When done, the cake will spring back when lightly pressed in the center and will have begun to pull away from the sides of the pan. If you stick a toothpick in it, it should come out clean.
7. Cool on a rack for 10 minutes. Run a small knife or metal spatula around the sides of the pans, and invert the cakes onto a cooling rack. Cool completely before icing.

Make the Buttercream

1. In a medium mixing bowl, combine the egg whites, salt, and sugar and stir to combine. Place over a pan of simmering water and heat the egg white/sugar mixture until the sugar is completely dissolved and the temperature reaches 180°F [82°C]. Use a candy or meat thermometer to assess the temperature. Stir occasionally.
2. In the meantime, melt the chocolate in a small pan, stirring constantly, or in a double boiler, and let it cool to room temperature.
3. Transfer the egg white mixture to the bowl of a stand mixer. Using the whisk attachment, whip the mixture on high speed until it doubles in volume, becomes thick and shiny, and has cooled to room temperature. Touch the bottom of the mixing bowl to assess the temperature. The next step is to add the butter. If the egg mixture is too hot, the butter will melt and ruin the buttercream.
4. When the egg white mixture is at room temperature, put the mixer on medium speed and add the soft butter, a piece at a time, until all is incorporated. The butter should be approximately the same temperature as the egg mixture to ensure easy incorporation and a smooth texture.
5. Add the vanilla and the melted chocolate and mix to incorporate. Beat on high speed for 1 minute to ensure that all the butter is combined with the whipped egg white and sugar mixture. Scrape the sides of the bowl and mix briefly to make sure the buttercream is homogeneous.
6. Use the buttercream immediately or place in an airtight container and refrigerate for up to a week or freeze for up to 3 months. If you refrigerate it, let it come to room temperature before using. This could take at least 6 hours, so we recommend removing it from the refrigerator the day prior to using it. You’ll want to re-whip the buttercream before using.

Assemble the Cake

1. Place one cake layer upside down on a 9-inch [23-cm] cake board or on a serving tray. If it has domed dramatically, remove the domed top with a serrated knife so that the layer is level. Take enough buttercream to make a 1⁄2-in [1.5-cm] layer of filling and spread it evenly over the surface.
2. Place the second cake layer upside down on top of the buttercream, removing any dome first, if necessary. Use the remaining buttercream to ice the exterior of the cake. Ice the sides and top smoothly if you’re planning to pipe a border on the edges. Ice rustically, swirling the buttercream with your spatula, if you prefer not to have a border.
3. If you choose to make a border, reserve some of the buttercream and put it in a pastry bag with a star tip. Pipe a border around the top and bottom edges.